Welcome to the VanDyke Software Forums

Join the discussion today!


Go Back   VanDyke Software Forums > General

Reply
 
Thread Tools Display Modes
  #1  
Old 08-20-2019, 09:23 PM
Stos Stos is offline
Registered User
 
Join Date: Aug 2019
Posts: 1
Line Breaks

I seem to be having an issue with additional line breaks being inserted between lines in SecureCRT.

As an example, where a coworker would normally see something like:

Code:
switch-1#sh cdp nei

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, 
                  D - Remote, C - CVTA, M - Two-port Mac Relay 



Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
SEP3CCE7359E68F  Gig 1/0/19        174             H P M  IP Phone  Port 1
SEP3CCE73ACAB19  Gig 1/0/36        157             H P M  IP Phone  Port 1
SEP3CCE73ACAB1E  Gig 1/0/17        166             H P M  IP Phone  Port 1
SEPA45630BBDDB2  Gig 1/0/20        149             H P M  IP Phone  Port 1
SEP68BDABA5C011  Gig 1/0/16        165             H P M  IP Phone  Port 1
SEP00082FB64DF6  Gig 1/0/21        167             H P M  IP Phone  Port 1
SEP3CCE7358443D  Gig 1/0/18        167             H P M  IP Phone  Port 1
I instead get:

Code:
switch-1# sh cdp nei

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, 

                  D - Remote, C - CVTA, M - Two-port Mac Relay 



Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID


SEP3CCE7359E68F  Gig 1/0/19        174             H P M  IP Phone  Port 1

SEP3CCE73ACAB19  Gig 1/0/36        157             H P M  IP Phone  Port 1

SEP3CCE73ACAB1E  Gig 1/0/17        166             H P M  IP Phone  Port 1

SEPA45630BBDDB2  Gig 1/0/20        149             H P M  IP Phone  Port 1

SEP68BDABA5C011  Gig 1/0/16        165             H P M  IP Phone  Port 1

SEP00082FB64DF6  Gig 1/0/21        167             H P M  IP Phone  Port 1

SEP3CCE7358443D  Gig 1/0/18        167             H P M  IP Phone  Port 1
These do appear both inside and outside of cisco devices. At first I thought this was a line spacing issue because the spaces between lines are not themselves selectable within SecureCRT. However when copy/pasting to notepad++ or excel for example, they do show up as separate line breaks/cells. This occurs regardless of which font is selected in SecureCRT settings.

I've already compared all my global and session settings with a coworker who doesn't have this issue, and we have not been able to find any differences there. We even had that coworker login with his own username on my workstation, and the issue persisted.
Reply With Quote
  #2  
Old 08-21-2019, 08:23 AM
bgagnon bgagnon is online now
VanDyke Technical Support
 
Join Date: Oct 2008
Posts: 3,972
Hi Stos,
Quote:
I've already compared all my global and session settings with a coworker who doesn't have this issue, and we have not been able to find any differences there. We even had that coworker login with his own username on my workstation, and the issue persisted.
Which does point to a configuration issue. I assume you compared just by looking through the Global/Session Options dialogs?

It's difficult to catch everything that way. You can share just a single session by drilling into the Sessions subfolder of your config folder and finding the corresponding INI file. Sort of what's described in this tip on migration/backup, but you would just grab the one file of interest. (As a note, a much easier way to accomplish migration/backup since v7.3.x is described in this tip.)

However, I think I may know the cause. In the Terminal / Emulation / Advanced category of Session Options, is Translate incoming CR to CR/LF enabled? If so and you disable it, is the issue resolved?
__________________
Thanks,
--Brenda

VanDyke Software
Technical Support
support@vandyke.com
(505) 332-5730
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 11:34 AM.